Menu

Non-contacting strain measurement techniques

images non-contacting strain measurement techniques

The half wave plate rotates the polarization vector by 90 degrees, thus allowing it to interfere with the unaltered beam to create an interference pattern on the surface of the object. SlideShare Explore Search You. Evaluation with Hz By parallelized image evaluation on graphics cards, the strain can be measured without contact at more than Hz — previously with optical systems, only measuring rates up to Hz were possible. See our Privacy Policy and User Agreement for details. Strain gages are more cost effective but are limited in the maximum allowable strain, require careful alignment and bonding techniques for a single use, and are also limited in their temperature range. Their biggest disadvantage, though, is their slow image processing speed, which limits the measuring and, therefore, the control frequency. The setup of the dynamic tensile testing is presented in Fig.

  • Strain Measurement Techniques for Composites Testing

  • Using the latest non-contact strain measurement provides new potential for fatigue testing of composite materials, by making continuous measurements of global. A novel non-contact strain measurement technique utilising Rayleigh waves.

    Abstract: Many devices that are used to convert a mechanical force or load to an.

    Strain Measurement Techniques for Composites Testing

    Non-contact. Full Field Strain. Measurement LaVision's StrainMaster system is a contactless instrument for materials testing and strain measurement. Applicable to a wide range of industries and materials, this optical technique avoids.
    Now customize the name of a clipboard to store your clips.

    Shear: Matrix dominant property, transferring stresses across the composite.

    It exhibits elastic-plastic behavior with large failure strain. Both detectors are connected to a control and display unit. No Downloads. In this way, project partners receive higher accuracy measurement data for even more precise predictions of the component lifetime.

    Visibility Others can see my Clipboard.

    images non-contacting strain measurement techniques
    Non-contacting strain measurement techniques
    Published in: Engineering.

    images non-contacting strain measurement techniques

    At the strain rate of s-1, the difference between these two measurements was large 0. Now customize the name of a clipboard to store your clips. A high speed accessory is necessary to convert optical signals to electronic signals in the form of sinusoidal waves and transfer them through high speed data acquisition to a digital recording format.

    images non-contacting strain measurement techniques

    Each of these variables constrains the range of applicability for a particular extensometer. Surface displacement is measured for each of the two locations and the differential displacement removing rigid body motions is converted to an average strain measure between the points [15].

    Non-contact methods are also attractive in applications where used for non- contact strain measurement in materials testing applications?. A wide variety of techniques exists for measuring strain in the tensile test;.

    If the contact does not faithfully transmit the strain from the test piece to wire or foil of. Strain measurements are used for a variety of health monitoring techniques. Non-contacting strain measuring techniques do not, in themselves, suffer any.
    If the specimen surface is fixed relative to the extensometer, the AC signal will have a frequency of precisely kHz. These measurements place high demands on the measuring speed of the strain measurement systems which are used.

    AAT6 is ductile, heat treated and artificially aged, containing magnesium and silicon as its major alloying element.

    Model However, components based on high-performance materials have to be qualified in each case in order to ensure the resilience and safety of the subsequent product. Cement boards are made with 4 layers of fabrics.

    images non-contacting strain measurement techniques

    The will, for example, enable the damage development to be analyzed both in real-time or subsequently.

    images non-contacting strain measurement techniques
    Stephen colbert metaphorical treadmill
    Instron Follow.

    Video: Non-contacting strain measurement techniques Strain gage(gauge) sensitivity - measure 1 microstrain or less

    The dynamic tensile tests are conducted using a MTS servo-hydraulic high rate testing machine in open-loop control. Views Total views. Keywords: dynamic tensile testing; laser extensometer; phase-shift; cement composites.

    July 17, Materials for light construction and high-temperature applications first have to be qualified before use in order to be able to utilize them to their full potential.

    Both detectors are connected to a control and display unit.

    Video: Non-contacting strain measurement techniques Webinar: Stop using strain gages!

    See our User Agreement and Privacy Policy.

    4 thoughts on “Non-contacting strain measurement techniques”

    1. Maukazahn:

      Both detectors are connected to a control and display unit. Overall, the strain time histories of specimens derived from laser extensometer agreed with actuator measurement for most of tests.

    2. Akinozshura:

      The failure behavior of the composite was also discussed using the images captured by high speed camera. At the strain rate of s-1, the difference between these two measurements was large 0.

    3. Nikosho:

      Each of these variables constrains the range of applicability for a particular extensometer. Cancel Save.

    4. Makasa:

      This eliminates the complex sample preparation for the application of artificial markers. If the specimen surface is fixed relative to the extensometer, the AC signal will have a frequency of precisely kHz.